Machining Cutting Speed
Calculate the machining cutting speed, Vc = (π·D·n) ÷ 1000, from the diameter D (mm — of the workpiece in turning or the tool in milling) and the rotation n (rpm). The result, in m/min, is the relative tangential speed between the cutting edge and the workpiece — the MOST important machining parameter, governing cutting temperature, tool wear, finish and productivity. Each workpiece-tool material combination has an optimal cutting-speed range recommended by makers: too high overheats and wears the tool fast (shortening life per Taylor's equation); too low cuts productivity and can cause built-up edge (BUE) and poor finish. Cutting speed is the starting point of any machining plan: from it and the diameter, the machine rpm is computed; it depends on material (steel, aluminum, titanium have very different ranges), tool material (HSS, carbide, ceramic) and operation. Enter the diameter and the rotation.
Resultado
—
Velocidade de corte na usinagem
A velocidade de corte na usinagem é Vc = (π·D·n) ÷ 1000, a partir do diâmetro D (da peça no torneamento ou da ferramenta no fresamento) e da rotação n. O resultado, em m/min, é a velocidade tangencial relativa entre a aresta de corte e a peça — o parâmetro mais importante da usinagem, pois governa a temperatura de corte, o desgaste da ferramenta, o acabamento e a produtividade. Cada combinação de material da peça e da ferramenta tem uma faixa ótima de velocidade de corte recomendada pelos fabricantes: velocidades muito altas superaquecem e desgastam rapidamente a ferramenta (reduzindo sua vida segundo a equação de Taylor); muito baixas reduzem a produtividade e podem causar aresta postiça de corte (BUE), que piora o acabamento. A velocidade de corte é o ponto de partida do planejamento de qualquer operação: a partir dela e do diâmetro calcula-se a rotação da máquina. Ela depende fortemente do material (aço, alumínio e titânio têm faixas muito diferentes — o alumínio admite velocidades altíssimas, o titânio exige velocidades baixas), do material da ferramenta (aço rápido, metal duro, cerâmica, CBN) e da operação (desbaste ou acabamento). Informe o diâmetro e a rotação.
Related Tools
Tool Life (Taylor's Equation)
Calculate a cutting tool's life by Taylor's equation, T = (C ÷ Vc)^(1/n), from the constant C (the cutting speed giving 1 minute of life, characteristic of the tool-material pair), the cutting speed Vc (m/min) and the exponent n (depending on tool material). Formulated by F. W. Taylor in 1907 from thousands of tests, this is machining's most famous relation and describes a fundamental trade-off: the HIGHER the cutting speed, the SHORTER the tool life — and steeply, since it is a power law. The exponent n quantifies the sensitivity: for HSS n ≈ 0.1 (life drops very fast with speed), for carbide n ≈ 0.2-0.3, for ceramic n ≈ 0.4-0.6 (less sensitive, allowing much higher speeds). Taylor's equation is the basis of economic OPTIMIZATION of machining: there is an optimal cutting speed minimizing total cost per part, balancing cutting time (falling with speed) against tool and change-downtime cost (rising with speed). Speeds above optimum 'burn' costly tools too fast; below, waste machine time. Enter the constant C, the cutting speed and the exponent n.
Cutting Force by the Kienzle Equation
Computes the main cutting force with the Kienzle equation, F_c = k_c1.1 · b · h^(1 − m_c), where k_c1.1 is the tabulated specific cutting force of the workpiece material for a reference chip section of 1 mm × 1 mm, b is the chip width and h the chip thickness, and m_c is the exponent describing the size effect. That is exactly where it differs from the direct calculation F_c = k_s·b·h: the latter treats specific pressure as a material constant, while Kienzle embeds the experimental fact that thin chips cost far more force per unit area, because the cutting edge radius stops being negligible next to the chip thickness. With k_c1.1 = 1500 N/mm² and m_c = 0.26, a 0.2 mm thick chip works at 2279 N/mm², 52 % above the tabulated value — which is why very low feeds raise the power spent per cubic millimetre removed, and the tool wear with it, instead of saving them — even though the absolute force falls. Since k_c1.1 carries a hidden millimetre raised to m_c, the equation is not dimensionally pure: thickness and width have to be entered in millimetres, and switching units is off by orders of magnitude. Enter the specific force k_c1.1, the exponent m_c, the chip width and the chip thickness.
Chip Thinning Corrected Feed per Tooth (Milling)
Computes the feed per tooth corrected for radial chip thinning in milling, f_z,corr = f_z / sin(φ_max), where sin(φ_max) = √(1 − (1 − 2·a_e/D)²) as long as the radial depth of cut a_e is less than half the cutter diameter D, and equals 1 above that. When the cutter engages little material sideways, each tooth enters and leaves the cut before reaching the point of maximum thickness, and the chip actually formed is THINNER than the programmed feed — the edge starts rubbing instead of cutting, generates heat, work-hardens the surface and wears fast, which is why light finishing passes often destroy tools quicker than heavy roughing. Correcting the feed restores the catalogue chip thickness: with a 12 mm cutter engaging only 1.2 mm, or 10 % of the diameter, the feed must rise 67 % for the tooth to cut at the intended thickness. Above half the diameter there is no thinning and the correction is neutral. Enter the target feed per tooth, the cutter diameter and the radial depth of cut.
Machining Cutting Force
Calculate the main cutting force in machining, F_c = k_s·a_p·f, from the specific cutting pressure k_s (N/mm², a workpiece-material property) and the cut section area (depth a_p × feed f, both mm). Cutting force is the main component of the force the tool exerts on the part (along the cutting-speed direction), and it sets the POWER required, the loads on the tool, holder, spindle and machine structure, and the part deflection. The specific cutting pressure k_s is the force per unit chip-section area, varying with material (steels ~1500-3000 N/mm², aluminum ~500-900, titanium and stainless much more), with feed (k_s drops at larger feeds — size effect) and with tool geometry. Knowing the cutting force is essential to: size the machine motor power, check that the fixturing (chuck, vise) holds, predict deflection of slender parts (causing dimensional error) and avoid tool breakage. It is a central machining process-planning calculation. Enter the specific cutting pressure, depth of cut and feed.
Machining Spindle Speed
Calculate the spindle speed (RPM) needed in machining, n = (1000·Vc) ÷ (π·D), from the desired cutting speed Vc (m/min) and the diameter D (mm — workpiece in turning or tool in milling). It is the inverse of the cutting-speed calculation, and the most used on the shop floor: the operator knows the material, picks the recommended cutting speed from tables, and must convert it to the rpm to set on the machine. The relation reveals a key point: for the same cutting speed, SMALLER-diameter parts or tools require HIGHER rpm (and vice versa). So turning a part of varying diameter (facing, tapers) at constant cutting speed requires continuously varying the rpm — done automatically by CNC lathes (G96, constant surface speed), while on conventional lathes the operator adjusts by ranges. Getting rpm right is essential for tool life, finish and safety (excessive rpm on large parts creates dangerous centrifugal forces). Enter the cutting speed and the diameter.
Machining Cutting Power
Calculate the cutting power in machining, P_c = (F_c·Vc) ÷ 60000, from the main cutting force F_c (N) and the cutting speed Vc (m/min); the result is in kW (60000 converts N·m/min to kW). Cutting power is the mechanical power the operation consumes to remove material, decisive for machine selection: the spindle motor must supply this power (plus losses, dividing by drive efficiency, typically 0.7-0.9) without stalling in the cut. If the required power exceeds the available, the machine loses speed, the cut jams or the tool breaks — so heavy roughing needs robust machines. Cutting power also relates to MRR by the specific cutting energy (P_c = u·Q, where u is energy per unit volume removed) — a practical alternative to estimate it directly from removed volume. Computing power is essential for planning (choosing the right machine), optimizing parameters (extracting the most from available power) and estimating energy use and heating. Enter the cutting force and the cutting speed.
The results provided by this tool are for general informational and educational purposes only and do not constitute professional, financial, medical, legal, tax or accounting advice. Always confirm important decisions with a qualified professional and official sources.