Cylindrical Shell MAWP
Calculate the maximum allowable working pressure (MAWP) of a pressure-vessel cylindrical shell, MAWP = (S·E·t) ÷ (r + 0.6·t), from the allowable stress S (MPa), the joint efficiency E, the available thickness t (mm, corrosion-deducted) and the internal radius r (mm). The MAWP is the MAXIMUM pressure a vessel can safely operate at the top, in the operating position, at the design temperature — one of a pressure vessel's most important numbers, stamped on its nameplate. It is the INVERSE of the thickness calculation: given the REAL available thickness (supplied, minus corrosion suffered), the maximum pressure it withstands is computed. MAWP is fundamental for several reasons: it sets the SAFETY-VALVE setting (which must open before pressure reaches MAWP, protecting the vessel from overpressure — the cause of explosions); it establishes the vessel's operating limit; and, recomputed periodically with the REMAINING thickness (measured by ultrasound at inspection, decreasing with corrosion), it monitors the vessel's 'health' over life — when MAWP drops below the operating pressure, the vessel must be repaired or retired. Each component (shell, heads) has a MAWP, and the vessel's is the smallest (the weakest component). Enter the allowable stress, efficiency, thickness and radius.
Result
—
Cylindrical shell MAWP
The maximum allowable working pressure (MAWP) of a cylindrical shell is MAWP = (S·E·t) ÷ (r + 0.6·t), from the allowable stress S, the joint efficiency E, the available thickness t (with the corrosion allowance already deducted) and the inside radius r. The MAWP is the highest pressure at which a vessel may safely operate, taken at the top of the vessel and at design temperature — one of the most important figures for any pressure vessel, and one that is stamped on the nameplate. It is the inverse of the thickness calculation: given the actual thickness available, it returns the maximum pressure that thickness will hold. The MAWP matters for several reasons: it sets the relief valve setting (the valve must lift before pressure reaches the MAWP, protecting the vessel from the overpressure that causes explosions); it establishes the operating limit; and, recalculated periodically with the remaining thickness (measured by ultrasonic testing at inspection), it tracks the health of the vessel throughout its service life — once the MAWP falls below the operating pressure, the vessel must be repaired or retired. Each component (shell, heads) has its own MAWP, and the MAWP of the vessel is the lowest of them, dictated by the weakest component. Enter the allowable stress, the joint efficiency, the thickness and the radius.
Related Tools
Cylindrical Shell Thickness (ASME)
Calculate the minimum wall thickness of a pressure-vessel cylindrical shell by the ASME Section VIII Division 1 formula, t = (P·r) ÷ (S·E − 0.6·P), from the internal design pressure P (MPa), the internal radius r (mm), the material allowable stress S (MPa) and the welded-joint efficiency E (0-1). The pressure vessel — used in boilers, chemical reactors, heat exchangers, compressed-air and LPG tanks, autoclaves — is a CRITICAL safety component: a failure under pressure can be explosive and catastrophic. So its design is rigorously codified, the ASME BPVC (Boiler and Pressure Vessel Code) being the world's most used. This formula gives the minimum cylindrical-shell thickness to safely resist the circumferential (hoop) stress. The '−0.6·P' term refines the thin-wall formula for moderately thick walls. The joint efficiency E (0.70 to 1.0, per weld type and radiographic-inspection degree) penalizes strength at the welded region — fully radiographed welds have E=1.0, uninspected welds lower E. The corrosion allowance is added to the calculated thickness. This is the central pressure-vessel design calculation, and underestimating is inadmissible. Enter the design pressure, internal radius, allowable stress and joint efficiency.
Hemispherical Head MAWP
Calculate the maximum allowable working pressure (MAWP) of a pressure-vessel hemispherical head, MAWP = (2·S·E·t) ÷ (r + 0.2·t), from the allowable stress S (MPa), the joint efficiency E, the available thickness t (mm) and the internal radius r (mm). Each pressure-vessel component has its own MAWP — the maximum pressure IT withstands with its available thickness — and the WHOLE vessel's MAWP is the SMALLEST among all its components' MAWPs (shell, heads, nozzles), since the vessel is as strong as its weakest component. This formula gives the hemispherical head's MAWP, the inverse of that head's thickness calculation. The factor 2 in the numerator (versus 1 in the shell) reflects the greater efficiency of the spherical form: for the same thickness, radius and material, the hemispherical head withstands about DOUBLE the cylindrical shell's pressure. So in a well-designed vessel with hemispherical heads, the cylindrical SHELL is usually the component governing the vessel's MAWP (the weakest), and the heads have margin. Comparing the components' MAWPs identifies the weakest link and guides repairs and reinforcements. Recomputing MAWP with the remaining thickness measured at inspection is part of vessel integrity management. Enter the allowable stress, efficiency, thickness and radius.
Vessel Allowable Stress (ASME)
Calculate the design allowable stress of a pressure-vessel material by the ASME criterion, S = σ_uts ÷ n, from the material minimum tensile strength σ_uts (MPa) and the safety factor n (3.5 in the current ASME VIII Div. 1 edition for tensile strength). The allowable stress S is the MAXIMUM stress permitted in the vessel material in service, and is the basis of all thickness and MAWP calculations — it embeds the safety margin against failure. The ASME code sets the allowable stress as the SMALLEST among several criteria: a fraction of the TENSILE strength (σ_uts/3.5 in the current edition — formerly /4.0, reduced as materials and inspection advanced), a fraction of the YIELD strength (2/3 of σ_yield), and, at high temperatures, criteria based on CREEP and creep rupture (since at high temperature the material deforms slowly under constant load). For each material and temperature, the code TABULATES the S value — this formula shows the tensile-strength criterion, often governing at moderate temperatures. Using the correct allowable stress (from the code, for the right material and temperature) is absolutely essential: it is the safety margin protecting against vessel explosion. Enter the tensile strength and the safety factor.
Hydrostatic Test Pressure
Calculate the hydrostatic test pressure of a pressure vessel by the (simplified) ASME rule, P_test = 1.3 · MAWP, from the maximum allowable working pressure MAWP (MPa). Before entering service (and periodically, at revalidations), every pressure vessel undergoes a HYDROSTATIC TEST: it is filled with WATER (not gas!) and pressurized ABOVE the operating pressure, to verify structural integrity and tightness before entrusting it with a hazardous fluid. ASME VIII Div. 1 (rule UG-99) requires a test pressure of 1.3 times MAWP (corrected by the allowable-stress ratio at test and design temperatures, simplified here). Using WATER is a fundamental safety matter: water is practically incompressible, so it stores very little energy when pressurized — if the vessel ruptures during the test, the failure is localized and relatively safe (it leaks, not explodes); whereas a compressed gas stores enormous energy and a rupture would be EXPLOSIVE, possibly lethal. The 1.3×MAWP test subjects the vessel to higher-than-operating stresses, revealing defects (cracks, bad welds, insufficient thickness) with margin, without reaching general yielding. Passing the hydrostatic test is a condition for the vessel's certification and operation. Enter the MAWP.
Torispherical Head Thickness (ASME)
Calculate the minimum thickness of a torispherical (standard flanged-and-dished) pressure-vessel head, t = (0.885·P·L) ÷ (S·E − 0.1·P), from the internal pressure P (MPa), the spherical crown radius L (mm), the allowable stress S (MPa) and the joint efficiency E. The TORISPHERICAL head is the most COMMON and economical head type in medium-pressure vessels (and universal in shallow tanks): it combines a central spherical crown (radius L) with a toroidal knuckle transition at the edge, joining the cylindrical shell — a form easier and cheaper to stamp than the hemispherical, and more compact (lower height). The 0.885 factor and formula hold for the standard ASME geometry with L ≈ D (crown radius equal to diameter) and the knuckle radius of 6% of the diameter. The price of the economy is a GREATER thickness than the hemispherical (the toroidal transition concentrates stress) and a critical knuckle region, where high bending stresses can arise. The torispherical head is the practical 'middle ground' between the costly hemispherical and the flat (which needs enormous thicknesses). This formula is essential in designing vessels with this head type. Enter the pressure, crown radius, allowable stress and joint efficiency.
Thickness with Corrosion Allowance
Calculate the total thickness to specify for a pressure-vessel component including the corrosion allowance, t_total = t_calculated + CA, from the minimum pressure-calculated thickness t_calculated (mm) and the corrosion allowance CA (mm). The thickness from the ASME formulas is the MINIMUM needed to resist pressure — but the vessel will operate for DECADES, and corrosion (and erosion) will consume wall material over time. If the vessel were made exactly at the minimum thickness, the first corrosion would already leave it below safe. So a CORROSION ALLOWANCE (CA) is added — a 'sacrificial' over-thickness, typically 1.5 to 6 mm, sized for the expected corrosion rate times the design life (e.g., 0.1 mm/year × 25 years = 2.5 mm). Thus the thickness specified for fabrication is the structural minimum plus the corrosion allowance. Over life, inspection (by ultrasound) measures the REMAINING thickness; when corrosion consumes the whole allowance and the thickness approaches the structural minimum, the vessel must be repaired or retired. The corrosion allowance is like a 'life reserve' built into the wall. Enter the calculated thickness and the corrosion allowance.
The results provided by this tool are for general informational and educational purposes only and do not constitute professional, financial, medical, legal, tax or accounting advice. Always confirm important decisions with a qualified professional and official sources.