Geosynthetic Tensile Stiffness
Calculate a geosynthetic's tensile stiffness (secant stiffness modulus), J = T ÷ ε, from the tensile force per unit width T (kN/m) and the corresponding strain ε (dimensionless, or ε/100 if in %); the result, in kN/m, is the stiffness. Unlike conventional materials, where stiffness is Young's modulus (stress/strain, in Pa), in geosynthetics the 'stress' is expressed per unit WIDTH (kN/m, since thickness is ill-defined and variable), so the stiffness J is also in kN/m. Tensile stiffness is fundamental in soil reinforcement design because geosynthetics only mobilize force when they DEFORM (stretch): the higher the stiffness J, the smaller the deformation needed to reach the required reinforcement force. This is crucial because reinforced-soil structures have ALLOWABLE deformation limits (a wall cannot bulge too much, an embankment cannot settle excessively) — so design is often controlled by stiffness (deformation) rather than strength (rupture). Modern reinforcement geosynthetics (polyester or HDPE geogrids) have high stiffness to limit deformations. Stiffness is measured in the wide-width tensile test, usually at a reference strain (2%, 5%). Enter the tensile force and the strain.
Resultado
—
Rigidez à tração de geossintético
A rigidez à tração (módulo de rigidez secante) de um geossintético é J = T ÷ ε, a partir da força de tração por unidade de largura T (kN/m) e da deformação correspondente ε; o resultado, em kN/m, é a rigidez. Diferente dos materiais convencionais, em que a rigidez é o módulo de Young (tensão/deformação, em Pa), nos geossintéticos a 'tensão' é expressa por unidade de largura (kN/m, pois a espessura é mal definida e variável), então a rigidez J também é em kN/m. A rigidez à tração é fundamental no projeto de reforço de solo porque os geossintéticos só mobilizam força quando se deformam (esticam): quanto maior a rigidez J, menor a deformação necessária para atingir a força de reforço requerida. Isso é crucial porque as estruturas de solo reforçado têm limites de deformação admissível (um muro não pode 'barrigar' demais, um aterro não pode recalcar excessivamente) — então o projeto é frequentemente controlado pela rigidez (deformação) e não pela resistência (ruptura). Geossintéticos de reforço modernos (geogrelhas de poliéster ou de PEAD) têm rigidez alta justamente para limitar deformações e atender aos critérios de serviço. A rigidez é medida no ensaio de tração de faixa larga, geralmente a uma deformação de referência (2%, 5%). Informe a força de tração e a deformação.
Related Tools
Reinforcement Tension per Layer (Geogrid)
Calculate the required tensile tension in a geosynthetic reinforcement layer in a reinforced-soil wall or slope, T_req = K_a·γ·z·S_v, from the active earth pressure coefficient K_a, the soil unit weight γ (kN/m³), the layer depth z (m) and the vertical spacing between layers S_v (m). In a reinforced-soil wall (geogrid walls, mechanically stabilized earth, reinforced steep slopes), each geosynthetic layer must resist the horizontal force the soil, under active pressure, tends to push out over that height band. The required tension grows with DEPTH (z), since lateral pressure increases with the vertical soil stress above — so the lower layers of a reinforced wall are the most stressed and sometimes get stronger geosynthetics or smaller spacing. The vertical spacing S_v sets each layer's 'influence area' (closer layers → less force each). Comparing T_req with the geosynthetic's allowable strength (and checking pullout), the reinforcement is designed: type, strength, spacing and length of each layer. It is the central calculation in reinforced-soil wall and slope design. Enter the active earth pressure coefficient, unit weight, depth and vertical spacing.
Geosynthetic Rupture Safety Factor
Calculate the safety factor against tensile rupture of a geosynthetic reinforcement layer, FS = T_adm ÷ T_req, from the allowable tensile strength T_adm (kN/m, the ultimate already reduced by creep, installation-damage and degradation factors) and the required tension T_req (kN/m, the force the soil demands at that layer). This is the final design check for a reinforcement layer: the available (allowable) strength must exceed the demand (required) with an adequate margin. Reinforced-soil codes require tensile-rupture safety factors typically around 1.3-1.5 (since many uncertainties — creep, damage, degradation — are already covered by the partial reduction factors embedded in T_adm). If FS is below the required, a stronger geosynthetic is chosen, the layer spacing reduced (lowering T_req per layer) or both. Besides tensile rupture (this calculation), reinforced-soil design also checks PULLOUT stability (sufficient anchorage), INTERNAL stability (failure surfaces cutting the reinforcements), EXTERNAL stability (sliding, overturning and bearing capacity of the whole mass) and deformations. This rupture FS is one of the fundamental checks. Enter the allowable strength and the required tension.
Allowable Geosynthetic Strength
Calculate the allowable (design) tensile strength of a geosynthetic, T_adm = T_ult ÷ (RF_cr·RF_id·RF_cd), from the ultimate strength T_ult (kN/m, from a short-term tensile test) and the reduction factors for creep RF_cr, installation damage RF_id and chemical/biological degradation RF_cd. Geosynthetics (geotextiles, geogrids, geomembranes) used as soil REINFORCEMENT in walls, slopes and embankments on soft soils must work for decades, and their design strength is far below the lab value from quick tests. The reduction factors discount: CREEP (polymers under constant load deform and lose strength over time, RF_cr typically 2-5, the largest factor); INSTALLATION DAMAGE (compacting gravel fill over the geosynthetic causes abrasion and punctures, RF_id ~1.1-2); and chemical/biological DEGRADATION over the service life (RF_cd ~1.1-2). Their product can reduce the allowable strength to 20-40% of the ultimate. This is the basis of designing any reinforced-soil structure, and underestimating the reduction factors (overestimating strength) is a cause of reinforced wall and slope failures. Enter the ultimate strength and the three reduction factors.
The results provided by this tool are for general informational and educational purposes only and do not constitute professional, financial, medical, legal, tax or accounting advice. Always confirm important decisions with a qualified professional and official sources.