Wire Rope Working Load Limit (WLL)
Calculate a wire rope's allowable working load, WLL = MBL ÷ SF, from the minimum breaking load (MBL, N) and the required safety factor. The working load (WLL — Working Load Limit, or SWL — Safe Working Load) is the MAXIMUM load that can be safely applied to a rope, fitting or lifting equipment — the information STAMPED on slings, shackles, hooks and equipment plates, and what the operator uses to decide whether a given load can be lifted. It is obtained by dividing the breaking load (the real strength that would break the component) by the code safety factor (5 for general lifting, more for special situations). Respecting the WLL is an absolute safety rule in lifting and material-handling: exceeding the working load dangerously approaches the component to rupture, eliminating the safety margin covering dynamic effects, wear and uncertainties. The WLL is not the rope's strength — it is the SAFE fraction of it. Every rigging operation starts by checking that the load to lift is below the WLL of each component in the load line (rope, slings, shackles, hook, eye), since the chain is only as strong as its weakest link. Enter the breaking load and the safety factor.
Resultado
—
Carga de trabalho de cabo de aço (WLL)
A carga de trabalho admissível de um cabo de aço é WLL = MBL ÷ FS, a partir da carga de ruptura mínima (MBL) e do fator de segurança exigido. A carga de trabalho (WLL — Working Load Limit, ou SWL — Safe Working Load) é a carga máxima que se pode aplicar com segurança a um cabo, acessório ou equipamento de içamento — é a informação que vem estampada nas lingas, manilhas, ganchos e na placa dos equipamentos, e a que o operador usa para decidir se pode levantar uma dada carga. Ela é obtida dividindo a carga de ruptura (a resistência real, que romperia o componente) pelo fator de segurança normativo (5 para içamento geral, mais para situações especiais). Respeitar a WLL é uma regra absoluta de segurança em operações de içamento: exceder a carga de trabalho aproxima perigosamente o componente da ruptura, eliminando a margem de segurança que cobre os efeitos dinâmicos, o desgaste e as incertezas. A WLL não é a resistência do cabo — é a fração segura dela. Toda operação de rigging começa por verificar que a carga a içar é menor que a WLL de cada componente da linha de carga (cabo, lingas, manilhas, gancho, olhal), pois a corrente é tão forte quanto seu elo mais fraco. Informe a carga de ruptura e o fator de segurança.
Related Tools
Wire Rope Safety Factor
Calculate a wire rope's safety factor, SF = breaking load ÷ working load, from the minimum breaking load (MBL, N) and the applied working load (N). Wire ropes, used in cranes, elevators, cableways, bridges, lifting and mooring, work with HIGH safety factors — far higher than static structures — for several reasons: the load is rarely static (there are impacts, accelerations, swings), the rope wears and loses strength over use (wires break, corrosion and fatigue occur), and a rupture is catastrophic (load drop, life risk). Codes prescribe minimum safety factors per application: typically 5 for general load lifting, 6-8 for people-carrying ropes (elevators, cableways), 3-4 for static stays and moorings, and specific values per use. The safety factor is the ratio between the load that would break the rope (its rated strength, from the maker) and the load it actually carries in service. Checking that the real safety factor meets the code minimum is the basic safety check of any wire-rope application — and the rope must be DISCARDED when wear reduces its strength enough for the factor to fall below the limit. Enter the breaking load and the working load.
Cable Tension in Accelerated Lift
Calculate the dynamic tension in a cable while lifting a load with acceleration, T = W·(1 + a/g), from the load weight W (N), the vertical lift acceleration a (m/s²) and gravity g. When a load is lifted with ACCELERATION (at lift start, when accelerating the rise), the cable must provide not only the force to support the weight (W) but ALSO the force to accelerate the mass upward — by Newton's second law, the total tension is the weight times the factor (1 + a/g). This means the DYNAMIC tension is GREATER than the static weight: an acceleration of g/2 (5 m/s²) raises the tension by 50%! That is why ABRUPT lifts (fast start, or worse, lifting an already-moving load or stopping abruptly) generate dangerous dynamic OVERLOADS in the cable, which can break it even with the static load within capacity. The effect is worse in abrupt STOPS and in loads 'snatching off the ground' (cable slack suddenly removed, generating an impact). So experienced operators lift SMOOTHLY (low acceleration), and the cable safety factors (5 or more) exist precisely to cover these inevitable dynamic overloads. This calculation quantifies the tension increase due to acceleration, essential in the safety analysis of dynamic lifts. Enter the load weight and the lift acceleration.
Rope-Pulley Contact Pressure
Calculate the contact pressure between a wire rope and a pulley (or drum) groove, p = 2·T ÷ (d·D), from the rope tension T (N), the rope diameter d (m) and the pulley diameter D (m); the result is in kPa. When a tensioned wire rope wraps a pulley, it presses the pulley groove with a contact pressure depending on tension and geometry. This pressure is a critical WEAR factor of the rope and pulley: high pressures (highly tensioned rope, small-diameter pulley, thick rope) accelerate abrasive wear of the rope's outer wires and the pulley groove wear, shortening both lives. Contact pressure is INVERSELY proportional to pulley diameter — so larger pulleys and drums extend rope life (besides reducing bending fatigue). Codes and makers specify allowable pressures per pulley material (steel, cast iron, polymer) and rope. With the D/d ratio (governing bending fatigue), contact pressure sets the rope-pulley system durability. Controlling contact pressure — using adequate pulleys and keeping tension within limits — is essential for the service life and safety of cranes, elevators and cableways. Enter the rope tension, the rope diameter and the pulley diameter.
The results provided by this tool are for general informational and educational purposes only and do not constitute professional, financial, medical, legal, tax or accounting advice. Always confirm important decisions with a qualified professional and official sources.