Gear Torque
Calculate the torque transmitted by a gear, T = (F_t·d) ÷ 2000, from the tangential force F_t (N) and the pitch diameter d (mm); the result is in N·m (the 2000 converts d/2 from mm to m). Torque is the moment the gear transmits about its axis, and the tangential force F_t acts at the pitch radius (d/2), creating that moment. This relation is the bridge between the POWER/torque side (what the shaft transmits) and the TOOTH-FORCE side (what sizes the strength): from shaft torque, the tooth tangential force (F_t = 2T/d) is obtained, which then feeds the bending (Lewis) and contact (Hertz) calculations. Conversely, given the tangential force, the torque is obtained. In a gear train, torque CHANGES at each stage by the gear ratio (a reduction that multiplies speed by 1/i multiplies torque by i, conserving power minus losses), while power stays roughly constant. So a reducer's last stage (low speed) transmits the HIGHEST torque and needs the most robust gears. Knowing the torque at each gear is essential to size teeth, shafts, keys and bearings. Enter the tangential force and the pitch diameter.
Resultado
—
Torque na engrenagem
O torque transmitido por uma engrenagem é T = (F_t·d) ÷ 2000, a partir da força tangencial F_t e do diâmetro primitivo d (em mm); o resultado é em N·m (o fator 2000 converte d/2 de mm para m). O torque é o momento que a engrenagem transmite em torno de seu eixo, e a força tangencial F_t atua no raio primitivo (d/2), gerando esse momento. Esta relação é a ponte entre o lado da potência/torque (o que o eixo transmite) e o lado da força nos dentes (o que dimensiona a resistência): a partir do torque do eixo, obtém-se a força tangencial nos dentes (F_t = 2T/d), que então alimenta os cálculos de flexão (Lewis) e contato (Hertz). Inversamente, conhecida a força tangencial, obtém-se o torque. Em um trem de engrenagens, o torque muda a cada estágio na razão de transmissão (uma redução que multiplica a velocidade por 1/i multiplica o torque por i, conservando a potência, descontadas as perdas), enquanto a potência se mantém aproximadamente constante. Por isso o último estágio de um redutor (baixa rotação) é o que transmite o maior torque e exige as engrenagens, os eixos e os mancais mais robustos. Conhecer o torque em cada engrenagem é essencial para dimensionar dentes, eixos, chavetas e mancais. Informe a força tangencial e o diâmetro primitivo.
Related Tools
Gear Dynamic Load
Calculate the effective dynamic load on gear teeth, F_d = F_t·K_v, from the nominal tangential force F_t (N) and the dynamic factor K_v. The dynamic load is the REAL tangential force the teeth bear in operation, larger than the nominal force (simply torque over radius) because of the dynamic effects of meshing at speed. These effects — vibrations, contact impacts, tooth deflections under load and manufacturing errors — make the instantaneous tooth load fluctuate and peak above the average, especially at high pitch-line velocities. The dynamic factor K_v (from Barth or other formulas) quantifies this amplification. The dynamic load is then used in strength checks: in Lewis bending stress (risk of tooth breakage at the root) and Hertzian contact stress (risk of surface fatigue and pitting). Using the nominal load without amplifying by the dynamic factor would underestimate the demands and lead to undersized gears that fail prematurely by fatigue. It is an essential, classic step in gear design. Enter the nominal tangential force and the dynamic factor.
Gear Base Diameter
Calculate the base circle diameter of an involute gear, d_b = d·cos(φ), from the pitch diameter d (mm) and the pressure angle φ (degrees). The base circle is the circle from which the INVOLUTE tooth profile is generated — the standard profile of modern gears. The involute is the curve traced by the tip of a string unwinding from a cylinder: that cylinder is exactly the base circle. The entire active tooth profile (the part that actually transmits force) is ABOVE the base circle; below it there is no involute profile. The base diameter is fundamental in gear geometry because it defines the involute profile and, with it, key properties: the LINE OF ACTION (the line tangent to both base circles of the mesh, along which tooth contact travels, always in the same direction — why involute gears transmit uniform motion), the base pitch and the contact ratio. The relation d_b = d·cos(φ) shows that the pressure angle is the angle between the line of action and the tangent to the pitch circles. It is an essential parameter in designing and manufacturing (generating) involute gears. Enter the pitch diameter and the pressure angle.
Tooth Thickness at Pitch Circle
Calculate the tooth thickness measured at the pitch circle of a standard gear, s = (π·m) ÷ 2, from the module m (mm). In a standard (uncorrected) gear, the circular pitch (the distance from one tooth to the next, along the pitch circle) is p = π·m, and it splits equally between the TOOTH (the solid part) and the SPACE (the gap between teeth): half each, hence s = π·m/2. This equality between tooth thickness and space width is what lets two standard gears of the same module mesh perfectly, with one's tooth fitting the other's space with proper clearance. Tooth thickness is a fundamental parameter: it sets the tooth STRENGTH (thicker teeth resist bending more) and the mesh backlash. In CORRECTED gears (with profile shift, used to avoid interference in small pinions, adjust center distance or balance pinion-gear strength), the pitch-circle tooth thickness DIFFERS from π·m/2 — it increases in a positively corrected pinion (strengthening it) and decreases in the gear. Measuring tooth thickness (by the chordal method, with a gear-tooth caliper, or over pins) is a classic gear quality-control check. Enter the module.
The results provided by this tool are for general informational and educational purposes only and do not constitute professional, financial, medical, legal, tax or accounting advice. Always confirm important decisions with a qualified professional and official sources.